首页
眉目
影响力0.00
经验值0.00
粉丝17
安全工程师
请问各路大侠从甘肃到新疆之间都有新建或扩建钢铁厂和焦 ...? 酒钢焦化5.5米捣固2*55查看更多
来自话题:
工厂停电时,UPS会给控制系统提供电源,若UPS无法供电或 ...? 我是新人,看了本帖学到很多啊查看更多
高手帮忙翻译一句话? 对编号为8825的合金用硫酸铁—硫酸法检测不到晶间腐蚀敏感性时,可采用astm a262 c测试方法即65%沸腾硝酸测试方法,该法对不锈钢晶间腐蚀敏感性的检测更灵敏,也可用其他特定的硝酸来检测。 注:astm a262共有五种方法检测晶间腐蚀敏感性,分别为a、b、c、e、f,每种方法侧重点不一样,c法是基于不锈钢热处理性能的。详细如下: intergranular corrosion test (igc) per astm a-262 at tcr engineering services, several methods exist for the testing of intergranular corrosion. to conduct these tests, we carefully choose a method which is suitable for the steel grade and grain boundary composition to be tested. intergranular corrosion in stainless steels may result from precipitation of carbides, nitrides or intermetallic phases. only in the most highly oxidizing solutions can intergranular attack be caused by intermetallic phases. when a test is to be restricted to carbides, in a material containing nitrides or intermetallic phases, a less oxidizing solution is chosen. the following tests are carried out by tcr engineering services in india as per the astm a262 specification. oxalic acid test, astm a262, practice a (oxalic acid etch) the oxalic acid etch test is a rapid method of screening those specimens of certain stainless steel grades which are essentially free of susceptibility to inter granular attack associated with chromium carbide participates. the test is used for acceptance but not rejection of material. ferric sulfate - sulfuric acid, astm a262 - practice b (streicher test) this test is based on weight loss determinations and provides a quantitative measure of the relative performance of the material evaluated. the procedure includes subjecting a specimen to a 24 to 120 hour boil in ferric sulfate - 50% sulfuric acid. this procedure measures the susceptibility of stainless steels and nickel alloys to inter granular attack associated with the precipitation of chromium carbides at grain boundaries. nitric acid, astm a262, practice c, (huey test) the specimens are boiled for five periods, each of 48 hours, in a 65 per cent solution of nitric acid. the corrosion rate during each boiling period is calculated from the decrease in the weight of the specimens. properly interpreted, the results can reveal whether or not the steel has been heat-treated in the correct manner. the customer must specify the maximum permissible corrosion rate and, in applicable cases, data on sensibilizing heat treatment. the huey test environment is strongly oxidizing, and, is only used as a check on whether the material has been correctly heat treated. this test is suitable for the detection of chromium depleted regions as well as intermetallic precipitations, like sigma phase, in the material. the huey test is also used for materials that come into contact with strongly oxidising agents, eg nitric acid. this procedure may also be used to check the effectiveness of stabilizing elements and of reductions in carbon content in reducing susceptibility to inter granular attack in chromium-nickel stainless steels. copper - copper sulfate - 16% sulfuric acid, astm a262 - practice e (strauss test) this procedure is conducted to determine the susceptibility of austenitic stainless steel to inter granular attack associated with the precipitation of chromium-rich carbides. once the specimen has been subjected to the solution boil, it is bent through 180° and over a diameter equal to the thickness of the specimen being bent. this test is based on a visual examination of the bent specimen. copper - copper sulfate - 50% sulfuric acid, astm a262 - practice f this test is based on weight loss determination which provides a quantitative measure of the relative performance of the material evaluated. it measures the susceptibility of "as received" stainless steels to inter granular attack.查看更多
来自话题:
TOC-4200 分析仪? 多路阀 这个不是燃烧法么 怎么会有多路阀 怎么说明呢,就是有很多白色细管连在一个像是由电机带动的装置查看更多
来自话题:
催化裂化收率预测公式(根据催化进料的残炭值、饱和烃含 ...? 这里计算得到的收率是什么收率?总液收?查看更多
来自话题:
除氰根 请教? z直接通氯吧,加点碱,这样可以不增加废水量 现在用的是双氧水处理,处理前是32000mg/l 现在处理到了30mg/l 投料我是按一个氰根对5个过氧化氢分子,这样将其处理成但其和二氧化碳,但这样耗费双氧水太多了,后续要将其处理符合0.5mg/l的排放标准 用次氯酸钠吗 这样的化处理成本又得增加了啊 还有就是双氧水处理后按机理里有氰酸根cno 目前不知道是不是氧化成了这个而不是氮气 这个氰酸根cno也没有检测方法啊 以上是我目前遇到的一些问题 直接通氯气考虑过 但是有点麻烦现在实验任务比较重就还没有做 直接通氯气的话你有没有更详细的建议呢 查看更多
来自话题:
求[萃取工]这本书? 本人认为这本书不如《萃取离子交换树脂》,因为我这里有这两本书,比较还是这本好啊查看更多
来自话题:
20万吨/年硫铁矿制酸装置开车时转化器升温要多久? 提供些资料,供参考: a.开车前提前通知干吸岗位开车进行酸循环。 b.将转化各冷激阀门,旁路阀门全关 ... 感谢你的热心解答! 只是我想要的答案还是没有,按照你提供的资料,“时通入含有约5%浓度的so2气体(气浓由净化补空气稀释而成)。一段触媒出口温度控制在 600℃范围内即可,若继续上升则将气浓继续调低,当温度升到某一温度点后温度开始回降,即表示一段催化剂已饱和。以下各段依此方法操作,各段催化剂已饱和后,再逐渐提高气浓,待各段催化剂都已饱和后,即按正常开车操作。”意思是催化剂饱和后即可达到工艺要的转化率吗? 查看更多
来自话题:
压力表头安装? 这种压力表本身精度都不高,你还横着,指针有自重的。 不光是指针自重,更主要游丝影响。查看更多
来自话题:
这是什么? 污泥吗 ~~查看更多
除了注化考证,生活还要很多内容——记录这几年的心酸考 ...? 希望楼主过查看更多
来自话题:
汽轮机的问题? 汽轮机的轴封就是迷宫密封。 既然都能吸住纸,那肯定就不能有蒸汽出来了。 那你们可以减小真空不?我觉得是不是你们的真空抽的太大了,导致空气进入缸体。 你可以试一试减小真空度的方法来看看这种现象还有不!查看更多
来自话题:
管道增压泵使用问题? 这没必要设缓冲罐吧查看更多
来自话题:
苯环上的格氏反应? 见烟台大学学报,1999,第2期[em11]查看更多
来自话题:
卧式容器使用耳式支座的计算? 这个问题比较复杂,也比较罕见。 我个人认为可以采用“圈座支承(新标准已经取消)+耳式支座”的形式计算。这样还能找到一些计算依据。要不就使用应力分析的方法。以上仅供参考。查看更多
来自话题:
比卡鲁胺前景如何? 此药销售额在处方药中已经挤进前五十位,应该有市场 查看更多
碱洗塔清洁剂在线清洗-MTO装置新的经济增长点? 如果神华包头应用效果好的话,会很快被各家效仿推广起来查看更多
关于化工设备机器螺栓防腐探讨? 无法拆卸接用液压剪切掉,[wiki]石油[/wiki]行业用的很多.查看更多
来自话题:
求助循环水指标要求 急!? 循环冷却水的水质标准表 ________________________________________ ________________________________________ 项目 单位 要求和使用条件 允许值 悬浮物 mg/l 根据生产工艺要求确定 gb50021 94的规定执行 硫酸根离子与氯离子之和 1500 硅酸 mg/l 175 镁离子与二氧化硅的乘积 15000 游离氯 mg/l 在回水总管处 0.5-1.0 石油类 mg/l 5 炼油企业 10 注: 甲基橙碱度以碳酸钙计; 硅酸以二氧化硅计; 镁离子以碳酸钙计。查看更多
在Aspen Plus中用caculator模块编制的excel表格如何保存 ...? 直接保存bkp就好,有apmbd文件共同生成。查看更多
简介
职业:广东重仪机械工程服务有限公司 - 安全工程师
学校:湘潭大学 - 化学学院
地区:河北省
个人简介:他清早的问候,他深夜的短信,他送来的礼物,不是因为他爱你,只是他无聊至极。查看更多
已连续签到天,累积获取个能量值
  • 第1天
  • 第2天
  • 第3天
  • 第4天
  • 第5天
  • 第6天
  • 第7天
 
这是一条消息提示
 
提醒
您好,您当前被封禁天,这天内您将不能登陆盖德问答,离解封时间还有
我已了解
提醒
提问需要5个能量值,您当前能量值为,请完成任务提升能量值
去查看任务