首页
双木.耳东.
影响力0.00
经验值0.00
粉丝16
设备工程师
来自话题:
管式炉烟道挡板? 你可否用星阀代替挡板,该问题可解决。查看更多
保温厚度及热量损失计算小软件? 很实用,平时做设计时有时会要计算保温厚度,有了这个小程序方便多了,谢谢分享 查看更多
关于采样器和取样器的区别? 没什么本质区别。如果非要区分这两个东西的叫法,一般都是那些在学校里搞教学的形而上学者们的专长。实际应用当中,对于现场操作者来说,叫什么无所谓,只要起到该起的作用才是硬道理。这不存在什么名不正言不顺的事。查看更多
来自话题:
脱盐水和冷冻盐水有什么区别? 为了安全,高于0度的冷冻水也应该采用冷冻盐水 防止负荷变化造成的温度变化造成水结冰查看更多
来自话题:
活塞杆在填料的部分表面层有部分脱落? 至于凹坑会不会是气体有杂质把活塞杆刮花.填料粉在坑到杆上查看更多
来自话题:
软化水每天上午再生反洗两小时,正常吗? 哎,软水处理,是很简单的问题啊。楼上说的耗盐量确实大了点,但是不知道处理能力是多大查看更多
罗茨机负荷重自么办? 备用的都好了,但需要等到停车才能并入系统,现在只能这样先开着,有什么办法查看更多
请教Maximum fractional capacity:和Maximum capacity f ...? 附上aspen自带的解释内容: for structured packings, aspen plus provides vendor procedures for each type. if you specify the maximum capacity factor, aspen plus bypasses the maximum capacity calculations. the definition of approach to maximum capacity depends on the type of packings. for norton imtp and intalox structured packings , approach to maximum capacity refers to the fractional approach to the maximum efficient capacity. efficient capacity is the operating point at which efficiency of the packing deteriorates due to liquid entrainment. the efficient capacity is approximately 10 to 20% below the flood point. for sulzer structured packings (bx, cy, kerapak, and mellapak), approach to maximum capacity refers to the fractional approach to maximum capacity. maximum capacity is the operating point at which a pressure drop of 12 mbar/m (1.47 in-water/ft) of packing is obtained. at this condition, stable operation is possible, but the gas load is higher than that at which maximum separation efficiency is achieved. the gas load corresponding to the maximum capacity is 5 to 10% below the flood point. sulzer recommends a usual design range between 0.5 and 0.8 for approach to flooding. for raschig random and structured packings , approach to maximum capacity refers to the fractional approach to maximum capacity. maximum capacity is at the loading point. for all other packings , approach to maximum capacity refers to the fractional approach to the flood point. because there are different definitions for approach to maximum capacity, sizing results are not on the same basis for packings from different vendors, even when you use the same value for approach to maximum capacity. direct performance comparison of packings from different vendors is not recommended. 我查了一下aspen自带的帮助文件,其中说的很明白,大家可以看看。 查看更多
来自话题:
精制正丙醇? 不知道你用的正丙醇是哪里生产的,用什么工艺成产的,为什么不更换不含丙酸正丙酯的正丙醇,这样不就省去了精制的步骤.据我所知,锦州石化实业公司生产的正丙醇中不含丙酸正丙酯,只是产量小点,而且湖南湘中制药厂和西安利君集团正在使用,而且使用了很长时间,效果很好.电话可以给你,方便的话可以联系一下:0416-412652 查看更多
来自话题:
有没有办法可以让固体酸代替硫酸催化生产1,4-二氧六环? 用双极膜 查看更多
来自话题:
DMF 的毒性? 真全,谢谢! 查看更多
来自话题:
压力管道管子材料的选择? 无特殊规范,业主要求和单位习惯!!查看更多
来自话题:
求2,4-二氯苯基异腈酸酯的合成路径? 别这么说啊,水平不够,正在积累啊 查看更多
项目投产后是否要发奖金? 如果换我做领导,我一定会发的,多少都要发一下,亏损了发少一点,告诉大家问题所在,期望在下一个项目时候改过来;盈利了要多发,鼓舞士气,为下一个项目做准备,告诉大家整个项目团队赚钱就表示大家赚钱,所谓同舟共济。查看更多
1kV YJV-3*50+1*25电缆中间怎么连接? 基本上都采用所叙述方法,注意连接处的保护,测试绝缘是否合格。查看更多
PROII自带的二元交互参数怎么利用? 看资料说,proii自带二元交互参数,不知道怎么利用? 高手帮帮忙,做个示范,谢谢了!! 不会是tools 里面的blv把?查看更多
来自话题:
天然气过滤分离器允许压降? 这个取决于你的流量,口径、目数等参数 或者你可以限定一个最大压降,供厂家复核查看更多
来自话题:
控制阀为何在机泵后面,能在前面不? 同意楼上的观点 如果你把控制阀关死的话,不就等于空泵运转~查看更多
工艺材料概算和工艺安装概算? 一般按照施工图计算出所需的材料,管道等要留出10%的余量。至于安装费用,有两种方式,一是套用定额,这种比较常用;二是大包,就是说事先定好完成工程多少钱。查看更多
从EPC的安装工程师到项目经理需要多远? 如果要做epc的项目经理的话 我们公司一般都是设计出身的 很少有施工出身的 查看更多
简介
职业:上海集泰化工有限公司 - 设备工程师
学校:西北民族大学 - 历史文化学院
地区:安徽省
个人简介:如果你吃了亏,千万不要喝水,不然你会变污的。查看更多
已连续签到天,累积获取个能量值
  • 第1天
  • 第2天
  • 第3天
  • 第4天
  • 第5天
  • 第6天
  • 第7天
 
这是一条消息提示
 
提醒
您好,您当前被封禁天,这天内您将不能登陆盖德问答,离解封时间还有
我已了解
提醒
提问需要5个能量值,您当前能量值为,请完成任务提升能量值
去查看任务