来大神帮我看看ba，谢谢咯？ 来大神帮我看看ba，谢谢咯 我把运行结果页翻译了一下，可还是不会修改block参数，帮我看看吧，通俗点~~~谢谢，急啊 << Run reinitialized 18:23:34 Thu May 30, 2013>> 运行重新启动于2013年五月30日下午6：23 ->Processing input specifications ...加载输入规范 ** ERROR IN THE "BLOCK" PARAGRAPH WHICH BEGINS ON LINE 157 BLOCK NAME: B12 MODEL NAME: DSTWU SKW: PARAM TKW: TEMP-TOL 错误开始发生在157行模块群 模块名称：B12 模型名称：DSTWU SKW:PARAM TKW:TEMP-TOL INVALID USE OF UNITS SPECIFICATION IN BRACES OR BRACKETS. SENTENCE IGNORED. 在括号或者括弧中的单位规范应用无效。 句子的忽略。 ** ERROR IN THE "BLOCK" PARAGRAPH WHICH BEGINS ON LINE 157 BLOCK NAME: B12 MODEL NAME: DSTWU SKW: PARAM TKW: FREE-WATER 错误开始发生在157行模块群 模块名称：B12 模型名称：DSTWU SKW:PARAM TKW:FREE-WATER VALUE IS REQUIRED FOR TERTIARY KEYWORD: HEAVYKEY BUT WAS NOT ENTERED. PARAGRAPH IGNORED. 值是第三关键字的所必需的：重关键组分 但是没有输入。 段落的忽略。 *** SEVERE ERROR BLOCK: "B12" APPEARS IN THE FLOWSHEET, BUT NO BLOCK PARAGRAPH HAS BEEN ENTERED FOR IT. 严重错误 模块：B12出现在流程中，但是却没有块段为其输入。 INFORMATION STREAM: "16" HAS NO SOURCE OR DESTINATION. IT WILL BE SAVED TEMPORARILY. 信息 流股：16没有源或者目的地。 它将暂时保存。 ! Errors while processing input specifications 处理输入规格时发生错误 ->Processing input specifications ...加载输入规范 Flowsheet Analysis :流程分析 Block $OLVER01 (Method: WEGSTEIN) has been defined to converge streams: 13 3 块$OLVER01（方法：WEGSTEIN）已经被定义为收敛流股：13 3 COMPUTATION ORDER FOR THE FLOWSHEET: $OLVER01 B12 B4 B20 B7 B8 B6 B11 REACTOR B5 DECANTER B21 (RETURN $OLVER01) 流程的计算秩序： $OLVER01 B12 B4 B20 B7 B8 B6 B11 REACTOR B5 DECANTER B21 (RETURN $OLVER01) ->Calculations begin ...计算开始 > Beginning Convergence Loop $OLVER01 Method: WEGSTEIN开始收敛循环$OLVER01方法：WEGSTEIN Block: B12 Model: DSTWU 模块：B12 模型：DSTWU ** ERROR MINIMUM REFLUX RATIO CALCULATED FROM UNDERWOOD EQUATION IS -1.3999. REFLUX RATIO RESET TO 0.1. ** 错误 由UNDERWOOD方程计算出的最小回流比 是-1.3999.回流比复位为0.1。 Block: B4 Model: FLASH2 Block: B20 Model: MIXER Block: B7 Model: HEATER Block: B8 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) *** SEVERE ERROR FORTRAN INVALID OPERATION ENCOUNTERED. *** 严重错误 FORTRAN语言遇到无效的操作。 ** ERROR LIQUID PHASE EXISTS EITHER AT OUTLET CONDITIONS OR AT SOME INTERMEDIATE CONDITIONS. SPECIFY "VALID PHASES" WHICH ALLOWS TWO OR THREE PHASES CALCULATION. ** 错误 液相不仅在出口条件也在一些中间条件存在。指定的“有效相态” 允许2或3个相态参与计算。 Block: B6 Model: HEATER Block: B11 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) * WARNING FEED STREAM IS BELOW DEW POINT AND "VALID PHASES" IS NOT SPECIFIED. TWO PHASES FLASH IS USED TO DETERMINE FEED STREAM PROPERTIES. * 警告 低于露点和有效相态的进料流未指定。 两个阶段的闪蒸是用来确定进料流性质的。 *** SEVERE ERROR FORTRAN DIVIDE BY ZERO ENCOUNTERED. *** 严重错误 FORTRAN语言遇到了除以0。 *** SEVERE ERROR SINGLE PHASE TEMPERATURE CALCULATIONS FAILED IN 3 ITERATIONS. FINAL TEMPERATURE IS 10.0000 FINAL ENTHALPY IS -2.5144D+08 SPECIFIED ENTHALPY IS -2.5686D+08 CALCULATION OF OUTLET TEMPERATURE FOR ISENTROPIC COMPRESSOR FAILED DUE TO ERROR IN FLASH. BLOCK IS BYPASSED. *** 严重错误 单相 温度计 算失败3次。 最后的温度是10，最后的焓是-2.5144D+08，指定的焓是-2.5686D+08，对于 等熵 压缩机 的出口温度计算错误是由于闪蒸罐被忽略了。 SKIPPING REST OF THE BLOCK CALCULATIONS. 跳过其余块的计算。 Block: REACTOR Model: RYIELD * WARNING SPECIFIED YIELDS HAVE BEEN NORMALIZED BY A FACTOR OF (0.98000) TO MAINTAIN AN OVERALL MATERIAL BALANCE. * 警告 为了保持总的物料平衡，收益率由一个因子（0.9800）归一化。 Block: B5 Model: HEATER Block: DECANTER Model: DECANTER * WARNING H2O WAS SPECIFIED AS AN L2-KEY COMPONENT BUT IS NOT PRESENT IN THE INLET STREAM. SPECIFICATION IGNORED. * 警告 水被指定为第二关键组分但是却并没有出现在进料流股。规范忽略。 Block: B21 Model: MIXER > Loop $OLVER01 Method: WEGSTEIN Iteration 1 6 vars not converged, Max Err/Tol 0.11161E+05 > 循环$OLVER01方法：WEGSTEIN 迭代16次不收敛，最大错误比上公差= 0.11161E+05 Block: B12 Model: DSTWU *** SEVERE ERROR THE LIGHT KEY COMPONENT IS NOT PRESENT IN THE FEED. BLOCK BYPASSED. *** 严重错误 轻关键组分没有出现在进料中。模块跳过。 Block: B4 Model: FLASH2 Block: B20 Model: MIXER Block: B7 Model: HEATER Block: B8 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) *** SEVERE ERROR FORTRAN INVALID OPERATION ENCOUNTERED. *** 严重错误 FORTRAN语言遇到无效操作。 ** ERROR LIQUID PHASE EXISTS EITHER AT OUTLET CONDITIONS OR AT SOME INTERMEDIATE CONDITIONS. SPECIFY "VALID PHASES" WHICH ALLOWS TWO OR THREE PHASES CALCULATION. ** 错误 液相不仅在出口条件也在一些中间条件存在。指定的“有效相态” 允许2或3个相态参与计算。 Block: B6 Model: HEATER Block: B11 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) * WARNING FEED STREAM IS BELOW DEW POINT AND "VALID PHASES" IS NOT SPECIFIED. TWO PHASES FLASH IS USED TO DETERMINE FEED STREAM PROPERTIES. * 警告 低于露点和有效相态的进料流未指定。 两个阶段的闪蒸是用来确定进料流性质的。 *** SEVERE ERROR FORTRAN DIVIDE BY ZERO ENCOUNTERED. *** 严重错误 FORTRAN语言遇到了除以0。 *** SEVERE ERROR SINGLE PHASE TEMPERATURE CALCULATIONS FAILED IN 3 ITERATIONS. FINAL TEMPERATURE IS 10.0000 FINAL ENTHALPY IS -2.5144D+08 SPECIFIED ENTHALPY IS -2.5686D+08 CALCULATION OF OUTLET TEMPERATURE FOR ISENTROPIC COMPRESSOR FAILED DUE TO ERROR IN FLASH. BLOCK IS BYPASSED. *** 严重错误 单相温度计算失败3次。 最后的温度是10，最后的焓是-2.5144D+08，指定的焓是-2.5686D+08，对于 等熵压缩机的出口温度计算错误是由于闪蒸罐被忽略了。 SKIPPING REST OF THE BLOCK CALCULATIONS. 跳过其余模块的计算 Block: REACTOR Model: RYIELD * WARNING SPECIFIED YIELDS HAVE BEEN NORMALIZED BY A FACTOR OF (0.98000) TO MAINTAIN AN OVERALL MATERIAL BALANCE. * 警告 为了保持总的物料平衡，收益率由一个因子（0.9800）归一化。 Block: B5 Model: HEATER Block: DECANTER Model: DECANTER * WARNING H2O WAS SPECIFIED AS AN L2-KEY COMPONENT BUT IS NOT PRESENT IN THE INLET STREAM. SPECIFICATION IGNORED. * 警告 水被指定为第二关键组分但是却并没有出现在进料流股。规范忽略。 Block: B21 Model: MIXER > Loop $OLVER01 Method: WEGSTEIN Iteration 2 2 vars not converged, Max Err/Tol -0.26537E+03 > 循环 $OLVER01 方法：WEGSTEIN 迭代22次没有收敛，最大错误比上公差= -0.26537E+03 Block: B12 Model: DSTWU *** SEVERE ERROR THE LIGHT KEY COMPONENT IS NOT PRESENT IN THE FEED. BLOCK BYPASSED. *** 严重错误 轻关键组分没有出现在进料中。模块跳过。 Block: B4 Model: FLASH2 Block: B20 Model: MIXER Block: B7 Model: HEATER Block: B8 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) *** SEVERE ERROR FORTRAN INVALID OPERATION ENCOUNTERED. *** 严重错误 FORTRAN语言遇到无效的操作。 ** ERROR LIQUID PHASE EXISTS EITHER AT OUTLET CONDITIONS OR AT SOME INTERMEDIATE CONDITIONS. SPECIFY "VALID PHASES" WHICH ALLOWS TWO OR THREE PHASES CALCULATION. ** 错误 液相不仅在出口条件也在一些中间条件存在。指定的“有效相态” 允许2或3个相态参与计算。 Block: B6 Model: HEATER Block: B11 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) * WARNING FEED STREAM IS BELOW DEW POINT AND "VALID PHASES" IS NOT SPECIFIED. TWO PHASES FLASH IS USED TO DETERMINE FEED STREAM PROPERTIES. * 警告 低于露点和有效相态的进料流未指定。 两个阶段的闪蒸是用来确定进料流性质的。 *** SEVERE ERROR FORTRAN DIVIDE BY ZERO ENCOUNTERED. *** 严重错误 FORTRAN语言遇到了除以0。 *** SEVERE ERROR SINGLE PHASE TEMPERATURE CALCULATIONS FAILED IN 3 ITERATIONS. FINAL TEMPERATURE IS 10.0000 FINAL ENTHALPY IS -2.5144D+08 SPECIFIED ENTHALPY IS -2.5686D+08 CALCULATION OF OUTLET TEMPERATURE FOR ISENTROPIC COMPRESSOR FAILED DUE TO ERROR IN FLASH. BLOCK IS BYPASSED. *** 严重错误 单相温度计算失败3次。 最后的温度是10，最后的焓是-2.5144D+08，指定的焓是-2.5686D+08，对于 等熵压缩机的出口温度计算错误是由于闪蒸罐被忽略了。 SKIPPING REST OF THE BLOCK CALCULATIONS. 跳过其余模块的计算 Block: REACTOR Model: RYIELD * WARNING SPECIFIED YIELDS HAVE BEEN NORMALIZED BY A FACTOR OF (0.98000) TO MAINTAIN AN OVERALL MATERIAL BALANCE. * 警告 为了保持总的物料平衡，收益率由一个因子（0.9800）归一化。 Block: B5 Model: HEATER Block: DECANTER Model: DECANTER * WARNING H2O WAS SPECIFIED AS AN L2-KEY COMPONENT BUT IS NOT PRESENT IN THE INLET STREAM. SPECIFICATION IGNORED. * 警告 水被指定为第二关键组分但是却并没有出现在进料流股。规范忽略。 Block: B21 Model: MIXER > Loop $OLVER01 Method: WEGSTEIN Iteration 3 2 vars not converged, Max Err/Tol -0.13630E+03 > 循环 $OLVER01 方法：WEGSTEIN 迭代32次没有收敛，最大错误比上公差=-0.13630E+03 Block: B12 Model: DSTWU *** SEVERE ERROR THE LIGHT KEY COMPONENT IS NOT PRESENT IN THE FEED. BLOCK BYPASSED. *** 严重错误 轻关键组分没有出现在进料流股中，模块忽略。 Block: B4 Model: FLASH2 Block: B20 Model: MIXER Block: B7 Model: HEATER Block: B8 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) *** SEVERE ERROR FORTRAN INVALID OPERATION ENCOUNTERED. *** 严重错误 FORTRAN语言遇到无效的操作。 ** ERROR LIQUID PHASE EXISTS EITHER AT OUTLET CONDITIONS OR AT SOME INTERMEDIATE CONDITIONS. SPECIFY "VALID PHASES" WHICH ALLOWS TWO OR THREE PHASES CALCULATION. ** 错误 液相不仅在出口条件也在一些中间条件存在。指定的“有效相态” 允许2或3个相态参与计算。 Block: B6 Model: HEATER Block: B11 Model: COMPR * WARNING IMPROPER OUTLET PRESSURE SPECIFIED FOR THE GIVEN UNIT INPUT PRESSURE = (0.6000E+07) OUTPUT PRESSURE = (0.6000E+07) * 警告 不当的出口压力为给定的单元指定 输入压力=(0.6000E+07) 出口压力=(0.6000E+07) * WARNING FEED STREAM IS BELOW DEW POINT AND "VALID PHASES" IS NOT SPECIFIED. TWO PHASES FLASH IS USED TO DETERMINE FEED STREAM PROPERTIES. * 警告 低于露点和有效相态的进料流未指定。 两个阶段的闪蒸是用来确定进料流性质的。 *** SEVERE ERROR FORTRAN DIVIDE BY ZERO ENCOUNTERED. *** 严重错误 FORTRAN语言遇到了除以0。 *** SEVERE ERROR SINGLE PHASE TEMPERATURE CALCULATIONS FAILED IN 3 ITERATIONS. FINAL TEMPERATURE IS 10.0000 FINAL ENTHALPY IS -2.5144D+08 SPECIFIED ENTHALPY IS -2.5686D+08 CALCULATION OF OUTLET TEMPERATURE FOR ISENTROPIC COMPRESSOR FAILED DUE TO ERROR IN FLASH. BLOCK IS BYPASSED. *** 严重错误 单相温度计算失败3次。 最后的温度是10，最后的焓是-2.5144D+08，指定的焓是-2.5686D+08，对于 等熵压缩机的出口温度计算错误是由于闪蒸罐被忽略了。 SKIPPING REST OF THE BLOCK CALCULATIONS. Block: REACTOR Model: RYIELD * WARNING SPECIFIED YIELDS HAVE BEEN NORMALIZED BY A FACTOR OF (0.98000) TO MAINTAIN AN OVERALL MATERIAL BALANCE. Block: B5 Model: HEATER Block: DECANTER Model: DECANTER * WARNING H2O WAS SPECIFIED AS AN L2-KEY COMPONENT BUT IS NOT PRESENT IN THE INLET STREAM. SPECIFICATION IGNORED. Block: B21 Model: MIXER > Loop $OLVER01 Method: WEGSTEIN Iteration 4 # Converged Max Err/Tol 0.00000E+00 ->Simulation calculations completed ... 查看更多14个回答 . 5人已关注
第1天
关注盖德视界
添加小助手
